Licensed & Insured, in Eugene and surrounding areas. Metal Roof Installation · Standing Seam Metal Roofing · Metal Roof Replacement.
Your Free Quote Request
All your work handled by qualified professionals in Eugene
Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.
Included in your service
Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.
Included in your service
Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.
Included in your service
Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.
Included in your service
Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.
Included in your service
Priority leak response: we trace the leak to its real source instead of caulking the symptom.
Included in your service
The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.
Included in your service
Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.
Included in your service
The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.
Included in your service
Steel strength under a textured stone finish, with strong hail and wind performance.
Included in your service
Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.
Included in your service
Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.
Included in your service
Flashing is the number one leak point on any metal roof, and it is what we fabricate best.
Included in your service
Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.
Included in your service
Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.
Included in your service
A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.
Included in your service
Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.
Included in your service
Barns, workshops, churches, and light commercial metal roofing across the county.
Included in your service
Reach us by phone at (541) 743-7131 or fill out the estimate form. We get back to you within 24 hours, no commitment required.
Our Metal Roofing Contractor visits your property, evaluates the project, and provides a written quote before any work begins.
Our crew completes the metal roofing and leaves your property clean and tidy. Full cleanup is included.
Continuous training, professional equipment, meticulous and code-compliant work
Full coverage on all our job sites, no exceptions
Emergencies, weekends, holidays: available when you need us
Response within 24h, no commitment, by phone or form
Available Mon-Sun 7am-7pm
We serve in Eugene and surrounding areas · On-site visits included · Free estimate within 24h
Eugene Metal Roofing is a team of local certified professionals based in Eugene. We respond quickly in Eugene and surrounding areas with professional equipment suited to every job.
Free estimate, transparent pricing, no subcontracting. Tell us about your roof. We'll handle the rest.
📞 Call (541) 743-7131⭐⭐⭐⭐⭐ 4.9/5 · 143 verified Google reviews
“We needed the roof redone on our hay barn before the rainy season hit and these guys knocked it out in two days flat. The corrugated panels went on straight and tight, and they cleaned up every last screw and scrap before leaving. Huge relief knowing the equipment and feed are finally dry.”
Commercial & Agricultural Metal Roofing
“Had them install a copper roof over our front entry and it looks absolutely stunning against the wood beams. They took their time getting the seams and flashing just right, and the crew clearly knew their way around specialty metal. Neighbors keep stopping to ask who did it.”
Copper & Specialty Metal Roofing
“Our old barn roof was rusted through in spots and we figured it was a goner, but Eugene Metal Roofing replaced the whole thing with new ribbed panels and it looks better than the house. Three-man crew, done in about three days, and they hauled off all the old tin. Honestly surprised at how painless it was.”
Metal Roof Replacement
“Went with standing seam for our place and I'm glad we did. The crew of four had roughly 2,200 square feet done in under a week, and the hidden fasteners make it look so clean. Only gripe is they showed up a day later than scheduled, but the work itself is flawless.”
Standing Seam Metal Roofing
“Had a leak over the kitchen every time it rained hard, and they tracked it down to failed screws and a bad flashing detail around the chimney. Fixed it in one afternoon and it's been bone dry through two storms since. Way cheaper than I was bracing for.”
Metal Roof Leak Repair
“We're tucked back in the trees and were dreading a full tear-off, but they did a metal roof over our existing shingles instead and saved us a ton of time and money. The crew was careful around all the low branches and even added snow guards since we get debris buildup. Couldn't be happier with how it turned out.”
Metal Roof Over Shingles (Retrofit)
“These folks came out for an inspection on our roof surrounded by big firs and were upfront that it just needed new screws and re-fastening in a few spots rather than anything major. They handled that on the spot and didn't try to upsell me on a replacement. Appreciate the honesty.”
Metal Roof Inspection
“After the windstorm tore up part of our roof, they came out fast and got the damaged panels and flashing repaired before the next rain. Communication was a little spotty during scheduling, but once the crew was here they were professional and thorough. Roof's solid again.”
Metal Roof RepairReal photos of our work in Eugene · Each image shows the final result achieved for our clients
Indicative estimates: your free personalized quote is always exact
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Exposed fastener panel roof | Starting at $8/sq ft | Corrugated or ribbed panels with underlayment and standard trim, best on simple gable roofs. |
| Standing seam metal roof | Starting at $12/sq ft | Concealed clips, formed flashing and premium finish, price rises with pitch and complexity. |
| Metal shingle or stone-coated steel | Starting at $14/sq ft | Textured systems on cut-up rooflines, cost moves with hips, valleys and dormers. |
| Tear-off and deck repair | Quoted per project | Removal of existing layers plus replacement of any rotten sheathing found during tear-off. |
| Travel | Included | In Eugene and surrounding areas, no separate call-out or mileage fee. |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Standing seam on a simple gable roof | Starting at $10/sq ft | Includes tear-off, underlayment, panels, and standard flashing on a straightforward pitch. |
| Standing seam on a cut-up roof | Starting at $13/sq ft | Valleys, dormers, and multiple penetrations add panels, custom flashing, and labor time. |
| Standing seam over existing shingles | On estimate | Code limits on existing layers and deck condition need an on-site look before pricing. |
| Deck repair or replacement | On estimate | Soft sheathing from years of wet winters is found after tear-off and priced per sheet. |
| Travel | Included | In Eugene and surrounding areas, no separate call-out or mileage fee. |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Tear-off and metal replacement, simple gable | Starting at $9/sq ft | Includes tear-off, deck inspection, underlayment, and new metal on a straightforward roof |
| Standing seam replacement | Starting at $12/sq ft | Concealed fasteners and raised seams, priced higher for material and detail work |
| Metal shingle or stone-coated steel | Starting at $11/sq ft | Stamped or granule-coated panels for historic districts and HOA design review |
| Complex roof with dormers and skylights | On estimate | Steep pitch, multiple valleys, and flashing details need an on-site look |
| Travel | Included | In Eugene and surrounding areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Exposed-fastener retrofit | Starting at $7/sq ft | Includes underlayment, purlins, and ribbed panel over one existing shingle layer; two layers add cost. |
| Standing seam retrofit | Starting at $11/sq ft | Concealed fasteners and raised seams; pitch and roof access drive the final number. |
| Metal shingle or stone-coated retrofit | Starting at $13/sq ft | Batten grid and stamped or coated panels; complex valleys and hips raise labor. |
| Flashing and penetration package | On estimate | New chimney, skylight, and sidewall flashing priced after an on-site count and condition check. |
| Travel | Included | in Eugene and surrounding areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Minor repair (reseal, fasteners, small flashing) | Starting at $450 | Covers resealing penetrations, replacing a few screws, or a small flashing fix; access and roof pitch move the price. |
| Single panel replacement | Starting at $850 | Includes removing the damaged panel, checking the deck, and installing a matching replacement; panel profile and availability affect cost. |
| Storm or limb damage repair | Starting at $1,200 | Covers securing the roof, replacing dented panels, and repairing flashing after wind or limb damage; scope depends on how many panels are hit. |
| Complex or large-scale repair | On estimate | Multi-panel damage, hidden deck rot, or steep hillside access needs an on-site look before we quote a number. |
| Travel | Included | in Eugene and surrounding areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Diagnostic leak trace and minor repair | Starting at $450 | Includes full roof walk, hose test, and a simple fix such as a boot or small flashing repair; pitch and height move the price. |
| Fastener and washer replacement (partial slope) | Starting at $650 | Covers pulling failed screws and installing new fasteners with EPDM washers on one slope; roof access and panel type drive cost. |
| Flashing, chimney, or skylight rebuild | Starting at $850 | Rebuilds the flashing detail with new metal and counterflashing; number of penetrations and roof pitch raise the total. |
| Emergency tarping after windstorm | Starting at $350 | Same-day or next-day tarp and temporary seal; urgency, roof height, and limb removal affect the final figure. |
| Complex or multi-source leak | On estimate | Needs an on-site look when several failures overlap or the water path crosses multiple roof planes. |
| Estimate | Free | Response within 24 hours at (541) 743-7131, no obligation to book the repair. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Spot re-fastening | Starting at $750 | Replaces isolated backed-out screws and cracked washers on a typical single-story roof. |
| Full panel-run re-screw | Starting at $1,450 | Pulls and resets every fastener on the runs, ridges, and eaves of a mid-size roof. |
| Oversized screw retrofit | Starting at $1,150 | Uses larger-diameter screws where stripped deck holes need a fresh bite. |
| Large two-story or shop roof | On estimate | Square footage, pitch, and fastener count need an on-site count before pricing. |
| Travel | Included | in Eugene and surrounding areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Corrugated panel installation | Starting at $5.50/sq ft | Includes panels, underlayment, trim and fasteners on standard single-slope and gable roofs |
| R-panel (ribbed) installation | Starting at $6.25/sq ft | Stronger spanning profile, priced higher on wider purlin spacing or steeper pitches |
| Retrofit over existing shingles | On estimate | Depends on shingle layer count, deck condition and whether purlins are needed |
| Repair and re-fastening | Starting at $450 | Covers screw replacement, washer renewal and closure repair on existing metal roofs |
| Travel | Included | in Eugene and surrounding Lane County areas, no separate mileage or call-out fee |
| Estimate | Free | Response within 24 hours at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Metal shingle roof, standard gable | Starting at $9/sq ft | Includes tear-off, underlayment, metal shingles and standard trim on a simple gable roof. |
| Metal shingle roof, complex roof | Starting at $12/sq ft | Steeper pitch, dormers, valleys and multiple penetrations raise labor and flashing time. |
| Retrofit over existing shingles | Starting at $8/sq ft | Skips tear-off where code allows one existing layer, saving disposal and labor cost. |
| Deck repair and sheathing replacement | On estimate | Soft or rotted sheathing found during tear-off needs an on-site look before pricing. |
| Travel | Included | In Eugene and surrounding Lane County areas, no separate call-out or mileage fee. |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Stone-coated steel over existing shingles | Starting at $9/sq ft | Includes underlayment and panels over one sound shingle layer where code allows |
| Full tear-off and new install | Starting at $12/sq ft | Includes tear-off, deck inspection, underlayment, panels, and flashing, with deck repair extra |
| Steep-pitch or complex roof | On estimate | Hillside homes near Spencer Butte need extra safety setup and staging before we quote |
| Travel | Included | in Eugene and surrounding Lane County areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Copper accent roof (porch, bay window, dormer) | Starting at $20/sq ft | Includes custom flat-lock or shingle copper and soldered details; small area and access drive the price. |
| Full copper standing seam roof | Starting at $32/sq ft | Includes fabricated panels, concealed clips and soldered seams; pitch and roof complexity raise the figure. |
| Zinc or aluminum specialty panels | Starting at $24/sq ft | Includes bare or pre-weathered metal and custom trim; modern geometry and flashing count move the number. |
| Copper-look metal shingle roof | Starting at $18/sq ft | Includes painted steel shingles finished as aged copper; roof size and tear-off add to the total. |
| Custom copper flashing and trim | On estimate | Chimney, skylight and valley metal fabricated in the shop; needs an on-site look before quoting. |
| Estimate | Free | Response within 24 hours at (541) 743-7131, no obligation to book the job. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Standard coating system | Starting at $2.50/sq ft | Includes cleaning, rust treatment and topcoat; heavier moss or pitted rust raises the rate |
| Rust conversion and recoat | Starting at $3.25/sq ft | Converter, primer and finish over oxidized panels; severity of pitting moves the price |
| Reflective cool-roof coating | Starting at $3.75/sq ft | High-reflectance finish for sun-exposed slopes; roof pitch and staging access affect cost |
| Complex or large-scale job | On estimate | Steep pitch, multiple levels or heavy moss needs an on-site look before a number |
| Travel | Included | In Eugene and surrounding areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Skylight re-flash (single unit) | Starting at $600 | Includes curb flashing replacement and boot seal; price rises with roof pitch and access difficulty. |
| Chimney counter-flashing repair | Starting at $850 | Custom bent metal set into masonry; cost moves with chimney width and masonry condition. |
| Step flashing and dormer rebuild | Starting at $950 | New step flashing laced into courses; higher on steep roofs or where deck repair is needed. |
| Cricket and diverter fabrication | On estimate | Built on site to fit the chimney and slope, so we inspect before quoting a number. |
| Travel | Included | In Eugene and surrounding Lane County areas, with no separate call-out or mileage fee. |
| Estimate | Free | Response within 24 hours at (541) 743-7131, with no obligation to book. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Bar guards over one entry or walkway | Starting at $1,200 | Includes hardware and installation for a short run above a door, steps, or deck. |
| Pad-style guard grid on standing seam | Starting at $1,650 | Covers a defined panel field; price moves with run length and seam spacing. |
| Full rail retention system | Starting at $2,400 | Continuous rails for long roof runs; cost depends on total linear feet and access. |
| Exposed-fastener guards on shop or barn | Starting at $1,400 | Sealed screw-mounted guards for ribbed panels; price varies with roof height and pitch. |
| Complex or steep-access installation | On estimate | Steep pitches, tall drops, or historic-district roofs need an on-site look first. |
| Estimate | Free | Response within 24 hours at (541) 743-7131, with no obligation to book. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Storm damage inspection | Free inspection | Full roof and attic-side photo documentation, written repair scope, no obligation to book |
| Spot panel and fastener repair | Starting at $350 | Single panel section, fastener replacement, and seam reseal included; pitch and access move the price |
| Flashing and penetration rebuild | Starting at $550 | Chimney, skylight, or vent flashing rebuilt to spec; number of penetrations drives cost |
| Section replacement or ridge repair | On estimate | Multiple damaged panels, crushed ridge, or underlayment damage need an on-site look first |
| Travel | Included | in Eugene and surrounding Lane County areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, written scope, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Standard metal roof inspection | Free estimate | Visual walk-through with photo notes, quoted free when repair or replacement work is being considered |
| Full condition assessment with written report | Starting at $250 | Fastener-by-fastener survey, seam and coating review, remaining service life estimate in writing |
| Pre-purchase or insurance documentation inspection | Starting at $350 | Full documented report timed to closing or claim deadlines, photos labeled for submission |
| Complex or large-scale roof | On estimate | Steep pitch, many penetrations or heavy moss and debris require an on-site look before quoting |
| Travel | Included | In Eugene and surrounding Lane County areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24 hours at (541) 743-7131, no obligation to book |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| 5-inch seamless aluminum gutter | Starting at $9/linear ft | Includes seamless trough, hidden hangers and basic downspouts for typical single-story Eugene homes. |
| 6-inch high-capacity gutter with screens | Starting at $14/linear ft | Wider trough, coarse leaf screen and 3x4 downspouts for heavy fir needle and maple leaf load. |
| Half-round or copper gutter | On estimate | Period profile or copper material priced after measuring runs, hanger type and panel profile. |
| Complex or large-scale job | On estimate | Multi-level roofs, steep Spencer Butte lots and long commercial runs need an on-site look first. |
| Travel | Included | in Eugene and surrounding Lane County areas, no separate call-out or mileage fee. |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book the work. |
| Service / Criteria | Indicative Rate | Details |
|---|---|---|
| Roof inspection and written scope | Free estimate | On-site walk, photos of failure points, and a written scope naming panel profile and fasteners |
| Through-fastened panel repair and re-fastening | Starting at $450 | Screw replacement, sealant renewal and localized flashing repair; price moves with roof height and access |
| Standing seam or insulated panel installation | On estimate | Priced per square foot after measuring span, slope, insulation and penetration count on site |
| Full tear-off and replacement | On estimate | Requires deck inspection and permit review before a number is given; old-layer count changes the scope |
| Travel | Included | In Eugene and surrounding Lane County areas, no separate call-out or mileage fee |
| Estimate | Free | Response within 24h at (541) 743-7131, no obligation to book |
Indicative rates, actual cost varies with project size, materials, and site access. Free personalized estimate within 24h.
Homeowners searching for a metal roofing contractor near me in Eugene want a crew that understands what local roofs actually face: steep pitches on Craftsman bungalows and hillside custom homes, heavy Douglas fir and bigleaf maple cover that keeps roofs shaded and damp, high-elevation exposure on the slopes above Spencer Butte and Hendricks Park, and a large stock of aging screw-down roofs whose fasteners are reaching the end of their service life. Eugene Metal Roofing is the local answer for metal roof installation, replacement, re-roof, and repair on mountain homes, backed by a network of licensed, insured local contractors who work in this climate every week.
We serve Eugene and surrounding areas, including Corvallis, Junction City, Coburg, and Creswell, handling everything from standing seam installs on new construction to leak repairs on 1990s subdivision roofs. If you are ready to talk through your roof, request a free estimate and we will give you a straight read on what your roof needs.
Most metal roof leaks in Eugene trace back to a handful of predictable failures, and the number one cause on 15 to 30 year old exposed-fastener roofs is fasteners backing out as their EPDM sealing washers dry, shrink, and crack. Once that washer fails, water finds the hole. The second common cause is seam separation from thermal movement, where panels expand and contract through hot summers and cold winters until a seam opens. Failed pipe boots and flashing at chimneys, skylights, and valleys let water slip behind the metal, and winter windstorms that drop limbs can lift panels or puncture them outright. Ice damming at the eaves on higher-elevation homes adds another path for water to back up under the panels.
Ignoring these problems is expensive. Water tracks along purlins and decking far from the entry point, so a small leak at a fastener can rot sheathing and saturate insulation several feet away before a stain shows up inside. That is why we inspect the whole roof system, not just the wet spot. Our metal roof repair work addresses the actual cause, whether that means replacing failed fasteners, re-sealing seams, or rebuilding flashing details.
The honest call between repair and replacement depends on the condition of the panels and the deck. On many aging screw-down roofs, a full screw replacement and re-fastening restores a watertight roof for a fraction of replacement cost, and we will tell you plainly when that is the right move. When panels are perforated or the deck is soft, replacement makes more sense. For active leaks, call (541) 743-7131 or contact us to schedule an inspection.
We install the full range of metal roofing systems and match the system to the home, not the other way around. Standing Seam Metal Roofing uses concealed clips and hidden fasteners, making it the premium choice with no exposed screws to maintain over its life. Corrugated & Ribbed Panel Roofing is the economical workhorse for cabins, barns, and workshops, and it performs well when fasteners are serviced on schedule. We also install Metal Shingle Roofing and Stone-Coated Steel Roofing for homeowners who want a traditional look, plus Copper & Specialty Metal Roofing for accents and distinctive details.
The honest comparison is simple: standing seam costs more up front but has no exposed screws to maintain, while screw-down costs less and needs its fasteners serviced over its life. When the deck is sound, Metal Roof Over Shingles (Retrofit) is a legitimate option that saves on tear-off; when the deck is not sound, tear-off is the right call.
Metal roof installation in Eugene is typically quoted per square foot, while repairs are often flat-rate, and the price depends on the panel system and metal gauge, roof pitch and complexity, tear-off versus recover, decking condition, and access. We frame all figures as typical ranges, and final pricing depends on the roof and site conditions. Some carriers may offer premium discounts for metal or impact-rated roofs, but that is between you and your insurer. For a closer look at how we structure numbers, see our pricing page.
To get a real number for your roof, request a free estimate or a free roof inspection. We will walk the roof, document what we find, and give you a clear written scope so you can compare options honestly.
After a windstorm or ice event, we inspect the roof and provide written documentation with photos that you may submit to your own insurer. We are not an insurance adjuster or agent, coverage decisions rest with your carrier, and we make no promise that a claim will be approved. On permits, in most jurisdictions a permit is commonly required for a full replacement or re-roof, but requirements vary by city, and thresholds, fees, and inspection requirements differ. Historic district or HOA design review can also affect panel profile and color choices. We do not state specific thresholds or fees because they change and must be verified locally.
Requirements vary, always verify with the Eugene building or planning department before starting your project. If you have questions about documentation or next steps, contact us and we will help you understand what your project involves.
Ready to get started? Eugene Metal Roofing serves in Eugene and surrounding areas. Get your free, no-obligation estimate today.
Get a Free EstimateMetal Roofing in Eugene · Response within 24h · No commitment · ☎ (541) 743-7131
Your Free Quote Request